146 lines
4.6 KiB
Markdown
146 lines
4.6 KiB
Markdown
# How to restart GitLab
|
|
|
|
Depending on how you installed GitLab, there are different methods to restart
|
|
its service(s).
|
|
|
|
If you want the TL;DR versions, jump to:
|
|
|
|
- [Omnibus GitLab restart](#omnibus-gitlab-restart)
|
|
- [Omnibus GitLab reconfigure](#omnibus-gitlab-reconfigure)
|
|
- [Source installation restart](#installations-from-source)
|
|
|
|
## Omnibus installations
|
|
|
|
If you have used the [Omnibus packages][omnibus-dl] to install GitLab, then
|
|
you should already have `gitlab-ctl` in your `PATH`.
|
|
|
|
`gitlab-ctl` interacts with the Omnibus packages and can be used to restart the
|
|
GitLab Rails application (Unicorn) as well as the other components, like:
|
|
|
|
- GitLab Workhorse
|
|
- Sidekiq
|
|
- PostgreSQL (if you are using the bundled one)
|
|
- NGINX (if you are using the bundled one)
|
|
- Redis (if you are using the bundled one)
|
|
- [Mailroom][]
|
|
- Logrotate
|
|
|
|
### Omnibus GitLab restart
|
|
|
|
There may be times in the documentation where you will be asked to _restart_
|
|
GitLab. In that case, you need to run the following command:
|
|
|
|
```bash
|
|
sudo gitlab-ctl restart
|
|
```
|
|
|
|
The output should be similar to this:
|
|
|
|
```
|
|
ok: run: gitlab-workhorse: (pid 11291) 1s
|
|
ok: run: logrotate: (pid 11299) 0s
|
|
ok: run: mailroom: (pid 11306) 0s
|
|
ok: run: nginx: (pid 11309) 0s
|
|
ok: run: postgresql: (pid 11316) 1s
|
|
ok: run: redis: (pid 11325) 0s
|
|
ok: run: sidekiq: (pid 11331) 1s
|
|
ok: run: unicorn: (pid 11338) 0s
|
|
```
|
|
|
|
To restart a component separately, you can append its service name to the
|
|
`restart` command. For example, to restart **only** NGINX you would run:
|
|
|
|
```bash
|
|
sudo gitlab-ctl restart nginx
|
|
```
|
|
|
|
To check the status of GitLab services, run:
|
|
|
|
```bash
|
|
sudo gitlab-ctl status
|
|
```
|
|
|
|
Notice that all services say `ok: run`.
|
|
|
|
Sometimes, components time out during the restart and sometimes they get stuck.
|
|
In that case, you can use `gitlab-ctl kill <service>` to send the `SIGKILL`
|
|
signal to the service, for example `sidekiq`. After that, a restart should
|
|
perform fine.
|
|
|
|
As a last resort, you can try to
|
|
[reconfigure GitLab](#omnibus-gitlab-reconfigure) instead.
|
|
|
|
### Omnibus GitLab reconfigure
|
|
|
|
There may be times in the documentation where you will be asked to _reconfigure_
|
|
GitLab. Remember that this method applies only for the Omnibus packages.
|
|
|
|
Reconfigure Omnibus GitLab with:
|
|
|
|
```bash
|
|
sudo gitlab-ctl reconfigure
|
|
```
|
|
|
|
Reconfiguring GitLab should occur in the event that something in its
|
|
configuration (`/etc/gitlab/gitlab.rb`) has changed.
|
|
|
|
When you run this command, [Chef], the underlying configuration management
|
|
application that powers Omnibus GitLab, will make sure that all directories,
|
|
permissions, services, etc., are in place and in the same shape that they were
|
|
initially shipped.
|
|
|
|
It will also restart GitLab components where needed, if any of their
|
|
configuration files have changed.
|
|
|
|
If you manually edit any files in `/var/opt/gitlab` that are managed by Chef,
|
|
running reconfigure will revert the changes AND restart the services that
|
|
depend on those files.
|
|
|
|
## Installations from source
|
|
|
|
If you have followed the official installation guide to [install GitLab from
|
|
source][install], run the following command to restart GitLab:
|
|
|
|
```
|
|
sudo service gitlab restart
|
|
```
|
|
|
|
The output should be similar to this:
|
|
|
|
```
|
|
Shutting down GitLab Unicorn
|
|
Shutting down GitLab Sidekiq
|
|
Shutting down GitLab Workhorse
|
|
Shutting down GitLab MailRoom
|
|
...
|
|
GitLab is not running.
|
|
Starting GitLab Unicorn
|
|
Starting GitLab Sidekiq
|
|
Starting GitLab Workhorse
|
|
Starting GitLab MailRoom
|
|
...
|
|
The GitLab Unicorn web server with pid 28059 is running.
|
|
The GitLab Sidekiq job dispatcher with pid 28176 is running.
|
|
The GitLab Workhorse with pid 28122 is running.
|
|
The GitLab MailRoom email processor with pid 28114 is running.
|
|
GitLab and all its components are up and running.
|
|
```
|
|
|
|
This should restart Unicorn, Sidekiq, GitLab Workhorse and [Mailroom][]
|
|
(if enabled). The init service file that does all the magic can be found on
|
|
your server in `/etc/init.d/gitlab`.
|
|
|
|
---
|
|
|
|
If you are using other init systems, like systemd, you can check the
|
|
[GitLab Recipes][gl-recipes] repository for some unofficial services. These are
|
|
**not** officially supported so use them at your own risk.
|
|
|
|
|
|
[omnibus-dl]: https://about.gitlab.com/downloads/ "Download the Omnibus packages"
|
|
[install]: ../install/installation.md "Documentation to install GitLab from source"
|
|
[mailroom]: reply_by_email.md "Used for replying by email in GitLab issues and merge requests"
|
|
[chef]: https://www.chef.io/chef/ "Chef official website"
|
|
[src-service]: https://gitlab.com/gitlab-org/gitlab-ce/blob/master/lib/support/init.d/gitlab "GitLab init service file"
|
|
[gl-recipes]: https://gitlab.com/gitlab-org/gitlab-recipes/tree/master/init "GitLab Recipes repository"
|